Nitrogen Oxides (NOx) – Regulation 13

The control of diesel engine NOx emissions is achieved through the survey and certification requirements leading to the issue of an Engine International Air Pollution Prevention (EIAPP) Certificate and the subsequent demonstration of in service compliance in accordance with the requirements of the mandatory, regulations 13.8 and 5.3.2 respectively, NOx Technical Code 2008 (resolution MEPC.177(58) as amended by resolution MEPC.251.(66)).

The NOx control requirements of Annex VI apply to installed marine diesel engine of over 130 kW output power other than those used solely for emergency purposes irrespective of the tonnage of the ship onto which such engines are installed.  Definitions of ‘installed’ and ‘marine diesel engine’ are given in regulations 2.12 and 2.14 respectively.  Different levels (Tiers) of control apply based on the ship construction date, a term defined in regulations 2.19 and hence 2.2, and within any particular Tier the actual limit value is determined from the engine’s rated speed:

  

Tier

Ship construction date on or after

Total weighted cycle emission limit (g/kWh)

n = engine’s rated speed (rpm)

n < 130

n = 130 - 1999

n ≥ 2000

I

1 January 2000

17.0

45·n(-0.2)

e.g., 720 rpm – 12.1

9.8

II

1 January 2011

14.4

44·n(-0.23)

e.g., 720 rpm – 9.7

7.7

III

1 January 2016

3.4

9·n(-0.2)

e.g., 720 rpm – 2.4

2.0

 

The Tier III controls apply only to the specified ships while operating in Emission Control Areas (ECA) established to limit NOx emissions, outside such areas the Tier II controls apply. In accordance with regulation 13.5.2, certain small ships would not be required to install Tier III engines.  

A marine diesel engine that is installed on a ship constructed on or after the following dates and operating in the following ECAs shall comply with the Tier III NOx standard:

.1         1 January 2016 and operating in the North American ECA and the United States Caribbean Sea ECA; or

.2         1 January 2021 and operating in the Baltic Sea ECA or the North Sea ECA.

The emission value for a diesel engine is to be determined in accordance with the NOx Technical Code 2008 in the case of Tier II and Tier III limits.  Most Tier I engines have been certified to the earlier, 1997, version of the NOx Technical Code which, in accordance with MEPC.1/Circ.679, may continue to be used in certain cases until 1 January 2011.  Certification issued in accordance with the 1997 NOx Technical Code would still remain valid over the service life of such engines.

An engine may be certified on an individual, Engine Family or Engine Group basis in accordance with one or more of the four duty test cycles as given in appendix II of the Annex.  In the case of Engine Family or Engine Group engines it is the Parent Engine which is actually emissions tested, this is the engine which has the combination of rating (power and speed) and NOx critical components, settings and operating values which results in the highest NOx emission value or, where more than one test cycle is to be certified, values which, to be acceptable, each of which must be no higher than the applicable Tier limit value. Subsequent series engines, Member Engines, are thereafter constructed with a rating, components, settings and operating values within the bounds established for the respective Engine Family or Engine Group. Generally all new engine certification leading to the issue of an EIAPP Certificate is undertaken at the engine builder’s works where the necessary pre-certification survey takes place.

Consequently a diesel engine having an EIAPP Certificate is approved, by, or on behalf of (since almost all engine certification work is delegated to Recognized Organizations), the flag State of the ship onto which it is to be installed, to a stated Tier for one or more duty test cycles, for a particular rating or rating range, and with defined NOx critical components, settings and operating values including options if applicable. Any amendments to these aspects are to be duly approved and documented.

For each NOx certified diesel engine there must be onboard an approved Technical File, NOx Technical Code 2008, regulation 2.3.4, which both defines the engine as approved and provides the applicable survey regime together with any relevant approved amendment documentation. As of October 2010 virtually all engines are surveyed using the Parameter Check method, NOx Technical Code 2008, regulation 2.4.3.1, whereby the actual duty, rating and NOx critical components, settings and operating values are checked against the given data in the Technical File. A key document in the Parameter Check procedure is the Record Book of Engine Parameters, NOx Technical Code 2008, regulation 6.2.2.8, which is maintained to record all replacements and changes to NOx critical components, settings and operating values. Engine surveys are undertaken on completion of manufacture and subsequently as part of the overall ship survey process; flowcharts illustrating the aspects checked at the various survey stages are given in NOx Technical Code 2008 appendix II.

In addition, there is the case where a diesel engine is subject to “major conversion”, regulation 13.2. Of the three routes given, “substantial modification” and uprating, both as defined, involve changes to an existing installed engine and under these circumstances the relevant Tier is that applicable to the construction date of the ship onto which the engine is installed except, in the case of ships constructed before 1 January 2000, where Tier I is applied. In the third route, that of the installation of a replacement, non-identical, or additional engine then the Tier appropriate to the date of installation applies although, subject to acceptance by the Administration taking into account guidelines, in some circumstances it would permitted to install a Tier II replacement engine as opposed to one certified to Tier III, regulation 13.2.2. In the case of an identical replacement engine the Tier appropriate to the ship construction date applies.

The revised Annex VI has also introduced the prospect of retrospective NOx certification, regulation 13.7, in the case of diesel engines of more than 5000 kW power output and a per cylinder displacement of 90 litres and above installed on ships constructed between 1 January 1990 and 31 December 1999. This will generally therefore affect only the main engines on such ships, the 90 litre/cylinder criteria represents, for example in current medium speed engine designs, engines with a bore of 460 mm and above. For these engines if a Party, not necessarily the ship’s flag State, has certified an "Approved Method" which results in an emission value no higher than the relevant Tier I level and has advised of that certification to IMO then that Approved Method must be applied no later than the first renewal survey which occurs more than 12 months after deposition of the advice to IMO.  However, if the ship owner can demonstrate that the Approved Method is not commercially available at that time then it is to be installed no later than the next annual survey after which it has become available. Given within regulation 13.7 are constraints on the Approved Method that limit its cost and detrimental effects on engine power and fuel consumption. Notifications of Approved Method from Parties are available through GISIS.

Further requirements are given in chapter 7 of the NOx Technical Code 2008 which includes an outline of the Approved Method File which must be retained with the engine. To date several notifications of Approved Methods have been advised to the Organization. It is not clear the extent to which others will become available however it is expected that, if so developed, these will be limited to involving aspects such as changing the engine’s fuel injection nozzles. Consequently, in the case of engines potentially subject to the requirement to install an Approved Method it will be necessary for ship owners (and also surveyors and port State inspectors) to remain vigilant over the service life of those engines as to the availability of such arrangements and to ensure that they are duly fitted and thereafter retained as required. For those engines where an Approved Method exists there is the alternative option, regulation 13.7.1.2, whereby the engine is instead certified in accordance with the conventional NOx Technical Code requirements.